您好,歡迎來到易龍商務網!
全國咨詢熱線:13605386905

武岡市大流量混流泵維修誠信企業

【廣告】

發布時間:2020-11-02 14:31  






混流泵

三)密封裝置是由填料函、水封圈、填料壓蓋和鉛粉(或油浸)石棉盤根填料組成。其作用有:

   1、啟動時防止空氣吸入泵內,起密封作用。

   2、抽水時防止水從泵內過多的沿軸大量流出。

III. Sealing equipment is composed of stuffing box,

water seal, packing gland,lead powder(or oil immersed)

asbestos

packing padding.Its use is as follows:

   1. When

starting, stop the pump from sucking air and realize the sealing function.

   2. When

drawing water, stop the water running out through the axle from pump.


 4、耗用功率太大

 The power

 cumption is too large

 1、轉速太高

 2、傳動軸彎曲

 3、填料壓得太緊

 4、軸承磨損或損壞

 5、葉輪和前蓋摩擦

 6、皮帶太緊

 1.The rotate speed is too high

 2.The drive shaft is bend

 3.The padding is too tight

 4.The bearing is worn out

 5.Impeller clashes the front cover

 6.The belt is too tight

 1、降低轉速

 2、校直

 3、擰松壓蓋螺栓或將填料取出打扁一些

 4、更換軸承

 5、調整葉輪端面軸向間隙

 6、適應放松

 1.Reduce the rotate speed

 2.Straightening

 3.Loose the cap blot or take our the

 padding and make it more flat

 4.Change the bearing

 5.Ajust the end play of impeller end face

 6.Loose the belt to suitable degree



 7、填料發熱

 The padding is

 hot

 1、填料壓得太緊或四周緊密度不夠2、填料壓得偏斜與軸磨損嚴重

 1.The padding is

 pressed too tight or the around compactness is not enough

 2.The padding is

 pressed deflected and the axile wears seriously

 1、旋松壓蓋螺栓高速填料緊密度

 2、松開壓蓋重新均勻地上緊

 1.Loosen the gland bolts to adjust

 2.Loosen the gland bolts and tighten it again.


2、離心泵的一般特點

(1)水沿離心泵的流經方向是沿葉輪的軸向吸入,垂直于軸向流出,即進出水流方向互成90°。

(2)由于離心泵靠葉輪進口形成真空吸水,因此在起動前必須向泵內和吸水管內灌注引水,或用真空泵抽氣,以排出空氣形成真空,而且泵殼和吸水管路必須嚴格密封,不得漏氣,否則形不成真空,也就吸不上水來。

(3)由于葉輪進口不可能形成絕  真空,因此離心泵吸水高度不能超過10米,加上水流經吸水管路帶來的沿程損失,實際允許安裝高度(水泵軸線距吸入水面的高度)遠小于10米。如安裝過高,則不吸水;水泵性能的技術參數有流量、吸程、揚程、軸功率、水功率、效率等。此外,由于山區比平原大氣壓力低,因此同一臺水泵在山區,特別是在高山區安裝時,其安裝高度應降低,否則也不能吸上水來。


行業推薦